LAB MANUAL FOR CCNA certexams com

Lab Manual For Ccna Certexams Com-PDF Download

  • Date:27 Jun 2020
  • Views:7
  • Downloads:3
  • Pages:73
  • Size:1.52 MB

Share Pdf : Lab Manual For Ccna Certexams Com

Download and Preview : Lab Manual For Ccna Certexams Com


Report CopyRight/DMCA Form For : Lab Manual For Ccna Certexams Com


Transcription:

3 4 Lab Exercise 4 Configuring Default route, 3 5 Lab Exercise 5 Implement and Verify Default Routes. 3 6 Lab Exercise 6 Configuring Loopback Interface, 3 7 Lab Exercise 7 Connectivity Tests with Traceroute. 3 8 Lab Exercise 8 Configuring RIP,3 9 Lab Exercise 9 Basic EIGRP Routing. 4 Exercises on RIP EIGRP Routing Scenarios, 4 1 Lab Exercise 1 RIP Routing Configuration Scenario. 4 2 Lab Exercise 2 Viewing IP RIP Information,4 3 Lab Exercise 3 Configuring RIPv2.
4 4 Lab Exercise 4 RIP2 Routes, 4 5 Lab Exercise 5 EIGRP Routing Configuration Scenario. 4 6 Lab Exercise 6 EIGRP Troubleshooting Lab Scenario. 4 7 Lab Exercise 7 EIGRP Show Commands,5 Exercises on OSPF. 5 1 Lab Exercise 1 OSPF Configuration in Single Area. 5 2 Lab Exercise 2 OSPF Troubleshooting Lab Scenario 1. 5 3 Lab Exercise 3 OSPF Troubleshooting Lab Scenario 2. 5 4 Lab Exercise 4 OSPF Routing Configuration Scenario. 6 Exercises on Access Lists, 6 1 Lab Exercise 1 Creating a Standard Access List. 6 2 Lab Exercise 2 Applying an Access List to an Interface. 6 3 Lab Exercise 3 View Access List Entries, 6 4 Lab Exercise 4 Standard Access List Scenario Lab 1. 6 5 Lab Exercise 5 Configuring and Verifying Standard Access List. 6 6 Lab Exercise 6 Configuring and Verifying Extended Access List. 6 7 Lab Exercise 7 Configuring and Implementing Extended Access List. 6 8 Lab Exercise 8 Named Access Lists,7 Exercises on Network Address Translation.
7 1 Lab Exercise 1 NAT Scenario 1,7 2 Lab Exercise 2 NAT Scenario 2. 7 3 Lab Exercise 3 Dynamic NAT Scenario 1,7 4 Lab Exercise 4 NAT and PAT. 8 Exercises on HSRP,8 1 Lab Exercise 1 To enable HSRP on a Router. 8 2 Lab Exercise 2 To disable HSRP on a Router,Version 4 0 Copyright 2002 2019 CertExams com 2. 8 3 Lab Exercise 3 Configuring HSRP Priority Delay and Preempt. 8 4 Lab Exercise 4 Load Sharing with Multigroup HSRP MHSRP. 9 Exercises on VPN Virtual Private Network, 9 1 Lab Exercise 1 Configuring site to site IPSEC VPN tunnel between routers.
10 Exercises on DHCP, 10 1 Lab Exercise 1 Configuring cisco router as a DHCP Server. 10 2 Lab Exercise 2 DHCP client configuration,11 Exercises on PPP. 11 1 Lab Exercise 1 PPP Configuration,12 Exercises on Frame Relay. 12 1 Lab Exercise 1 Configuring Frame Relay without sub interfaces. 12 2 Lab Exercise 2 Configuring Frame Relay with point to point sub interfaces. 12 3 Lab Exercise 3 Frame Relay Show Commands,13 Exercises on Ipv6. 13 1 Lab Exercise 1 Enabling IPv6 on a cisco router. 13 2 Lab Exercise 2 Enabling IPv6 on a cisco router interface. 13 3 Lab Exercise 3 Configuring IPv6 on a cisco router interface with Ipv6 address in. EUI format, 13 4 Lab Exercise 4 Configuring IPv6 on a cisco router interface with IPv6 address in.
general form, 13 5 Lab Exercise 5 Configuring loopback interface with IPv6 address. 13 6 Lab Exercise 6 Configuring IPv6 on two router interfaces connected directly and. pinging the distant interface using console,13 7 Lab Exercise 7 Configuring IPv6 static route. 13 8 Lab Exercise 8 Configuring IPv6 static default route. 13 9 Lab Exercise 9 Implement and verify IPv6 static route. 14 Exercises on IPv6 Routing Protocols, 14 1 Lab Exercise 1 Enabling RIPng on a cisco router interface. 14 2 Lab Exercise 2 Enabling RIPng on two routers and pinging between them. 14 3 Lab Exercise 3 Entering RIPng router configuration mode and setting global. parameters on a cisco router,Version 4 0 Copyright 2002 2019 CertExams com 3. 14 4 Lab Exercise 4 Configuring EIGRPv6 on a router interface. 14 5 Lab Exercise 5 Configuring EIGRPv6 on two routers and pinging between them. 14 6 Lab Exercise 6 Enabling OSPF for IPv6 on a cisco router interface. 14 7 Lab Exercise 7 Configuring OSPF on two router interfaces. 14 8 Lab Exercise 8 General IPv6 configuration on series router. 14 9 Lab Exercise 9 Traceroute lab,15 Exercises on BGP.
15 1 Lab Exercise 1 Basic BGP Configuration,15 2 Lab Exercise 2 Setting BGP attributes. 15 3 Lab Exercise 3 Setting the BGP neighbor password. 15 4 Lab Exercise 4 To disable the peer, 15 5 Lab Exercise 5 Basic Configuration of a Peer Group. 15 6 Lab Exercise 6 Configuring Multi Exit Discriminator Metric. 16 Exercises on Route Redistribution,16 1 Lab Exercise 1 Route Redistribution for RIP. 16 2 Lab Exercise 2 Route Redistribution for EIGRP. 16 3 Lab Exercise 3 Route Redistribution for OSPF, 16 4 Lab Exercise 4 Redistribution between EIGRP and OSPF. 16 5 Lab Exercise 5 Redistribution between RIP and EIGRP. 17 Exercises on MPLS, 17 1 Lab Exercise 1 Configuring a Router for MPLS Forwarding and verifying the.
configuration of MPLS forwarding,17 2 Lab Exercise 2 Enabling MPLS. 17 3 Lab Exercise 3 Configuring MPLS LDP,17 4 Lab Exercise 4 Configuring MPLS using EIGRP. 17 5 Lab Exercise 5 Configuring MPLS using OSPF,17 6 Lab Exercise 6 Configuring MPLS using RIP. 17 7 Lab Exercise 7 MPLS show commands,18 Cisco Switch IOS. 18 1 Logging into the switch,18 2 Lab Exercise 1 Introduction to Switch.
18 3 Lab Exercise 2 Switch Console Password Assignment. 18 4 Lab Exercise 3 Switch VTY Password Assignment. 18 5 Lab Exercise 4 Switch Privileged password, 18 6 Lab Exercise 5 Enable Fast Ethernet Interface on a Switch. 18 7 Lab Exercise 6 Initial Switch Configuration, 18 8 Lab Exercise 7 Basic Switch Interface Configuration. 18 9 Lab Exercise 8 Catalyst 2960S Switch Configuration. 19 Exercises on Spanning Tree Protocol,Version 4 0 Copyright 2002 2019 CertExams com 4. 19 1 Lab Exercise 1 Enabling STP,19 2 Lab Exercise 2 Configuring Root Switch. 19 3 Lab Exercise 3 Configuring Port Priority, 19 4 Lab Exercise 4 Configuring Switch Priority of a VLAN.
19 5 Lab Exercise 5 Configuring STP Timers,19 6 Lab Exercise 6 Verifying STP. 20 Exercises on Switch Configuration and VLAN,20 1 Lab Exercise 1 Basic Switch IP Configuration. 20 2 Lab Exercise 2 Configure and verify port security on switch. 20 3 Lab Exercise 3 Troubleshooting a Switch,20 4 Lab Exercise 4 Switch Trunking Configuration. 20 5 Lab Exercise 5 Creating and Deleting VLAN s,20 6 Lab Exercise 6 Configuring VTP on a Switch. 20 7 Lab Exercise 7 Configuring VTP with a VTP Client. 20 8 Lab Exercise 8 Troubleshooting lab with non matching domains. 20 9 Lab Exercise 9 Troubleshooting lab with trunk functionality. 20 10 Lab Exercise 10 VLANs Scenario,20 11 Lab Exercise 11 VTP Scenario.
20 12 Lab Exercise 12 VLANs and Trunking,20 13 Lab Exercise 13 Routing between VLANs. Version 4 0 Copyright 2002 2019 CertExams com 5,1 BASIC EXERCISES. Note Please refer to the below default network Diagram for all the exercises given in this. 1 1 Lab Exercise 1 Entering User EXEC prompt on a Router and exit. Description A basic exercise that shows how to enter into privileged EXEC prompt from user. mode prompt and exit from the same,Instructions,1 Enter into privileged mode. 2 Get back to the user mode,Version 4 0 Copyright 2002 2019 CertExams com 6. Password Cisco,BLR enable,BLR disable, 1 2 Lab Exercise 2 Introduction to Basic User Interface.
Description This exercise helps to get familiar with the user mode privileged mode CLI and. basic commands,Instructions,1 Press enter to get the router prompt. 2 In the user mode type the command used to view all the commands in user mode. 3 Enter into privileged mode, 4 In the privileged mode type the command to view all the commands in privileged mode. 5 The command show displays all the show commands like show access list show banner. show cdp show hosts show flash show protocols etc, 6 The command show running config displays the running configuration. 7 Press space bar to view more information,8 The command exit or disable logs out the router. BLR enable,BLR show running config,BLR disable,1 3 Lab Exercise 3 Basic show commands.
Description A basic exercise to get familiar and understand the various show commands. available in the privileged mode,Instructions,1 Enter into privileged mode. 2 Show running config displays the active configuration in memory The currently active. configuration script running on the router is referred to as the running config in the router s CLI. 3 Show flash memory Flash memory is a special kind of memory that contains the operating. system image file s on the router, 4 Show history command displays all the past commands still present in router s memory. 5 Show protocols command displays the protocols running on your router. Version 4 0 Copyright 2002 2019 CertExams com 7, 6 Show version command displays critical information such as router platform type operating. system revision operating system last boot time and file location amount of memory number of. interfaces and configuration register,7 Show clock command displays the router s clock. 8 Show hosts command displays list of hosts and all their interfaces IP Addresses. 9 Show users command displays list of users who are connected to the router. 10 Show interfaces command displays detailed information about each interface. BLR enable,BLR show running config,BLR show flash,BLR show history.
BLR show protocols,BLR show version,BLR show clock. BLR show hosts,BLR show interfaces,Below is the show protocols command output. Below is the show version command output,Version 4 0 Copyright 2002 2019 CertExams com 8. Below is the show clock command output,1 4 Short form commands. 1 copy running config startup config command can be interpreted and used in short form as. copy run start command, 2 show running config command can be interpreted and used in short form as show run.
3 show startup config command can be interpreted and used in short form as show start. 4 copy running config tftp command can be interpreted and used in short form as copy run tftp. 5 copy tftp startup config command can be interpreted and used in short form as copy tftp start. Note We can also use UP ARROW and DOWN ARROW keys to get the previously typed. command in the simulator,2 ROUTING IOS FUNDAMENTAL EXERCISES. 2 1 Lab Exercise 1 Banner MOTD Setting message of the day. Description This exercise helps in understanding the procedure of setting message of the day. and the show banner command Note that the banner is set in a single command line here You. can also use multi line banner motd command,Instructions. 1 Enter into privileged mode,2 Enter into global Configuration Mode. 3 Set banner to Welcome to local host Starting and ending character of the banner should be. Z Do not use quotes, 4 Use show banner command to view the banner that has been set. BLR enable,BLR configure terminal,BLR config banner motd Z Welcome to local host Z.
BLR config exit,BLR show running configuration,Version 4 0 Copyright 2002 2019 CertExams com 9. 2 2 Lab Exercise 2 Setting Host Name, Description This basic exercise illustrates the steps required to set a hostname to a router. Instructions,1 Enter into privileged mode,2 Enter into global Configuration Mode. 3 Set hostname as cisco,BLR enable,BLR configure terminal. BLR config hostname cisco,BLR config exit,BLR show running config.
You can give show running config command to check the output where hostname changed to. cisco from BLR,2 3 Lab Exercise 3 Router Interface Configuration. Description In this lab you will learn to enable interfaces on a router i e configure Serial 0 0 0 and. FastEthernet 0 0 interfaces on a router with specified IP Address and Subnet Mask. Instructions,Version 4 0 Copyright 2002 2019 CertExams com 10. 1 Enter into privileged mode,2 Enter into global Configuration Mode. 3 Set IP Address of Serial 0 0 0 as 192 168 1 2 and Subnet Mask as 255 255 255 5. 4 Set IP Address of FastEthernet 0 0 as 192 168 0 130 and Subnet Mask as 255 255 255 0. BLR enable,BLR configure terminal,BLR config interface serial 0 0 0. BLR config if ip address 192 168 1 2 255 255 255 0. BLR config if exit,BLR config interface fastethernet 0 0.
BLR config if ip address 192 168 0 130 255 255 255 0. By giving show running config command you can view the ip address configured on the interfaces. 2 4 Lab Exercise 4 Setting Bandwidth on an interface. Description Bandwidth refers to the rate at which data is transferred over the communication. link You setup the bandwidth on a given interface interface serial 0 0 0 to a specified value 64. kbps You also set the clockrate to 64000 Note that bandwidth is represented in kbps whereas. clock rate is entered in bps,Syntax bandwidth interface. The command bandwidth kilobits will set and communicate the bandwidth value for an. interface to higher level protocols, Ex bandwidth 64 will set the bandwidth to 64 kbps Use no form of the command to set the. Version 4 0 Copyright 2002 2019 CertExams com 11,bandwidth to default value. Instructions,1 Enter to serial 0 0 0 mode of router BLR. 2 Set bandwidth of serial 0 0 0 as 64 kbps,3 Set clockrate as 64000 bps.
BLR enable,BLR configure terminal,BLR config interface serial 0 0 0. BLR config if bandwidth 64, BLR config if clock rate 64000 This command applies to only DCE interfaces. BLR config if exit,BLR config exit,BLR show interface s 0 0 0. BLR show interfaces, Below is the show interfaces serial 0 0 0 command output. 2 5 Lab Exercise 5 Setting Console Password,Not Available in Demo Version.
LAB MANUAL FOR CCNA Version 4 0 CONTENTS 1 Basic Exercises 1 1 Lab Exercise 1 Entering user EXEC prompt on a Router and Exit 1 2 Lab Exercise 2 Introduction to Basic User Interface 1 3 Lab Exercise 3 Basic Show commands 1 4 Short Form Commands 2 Routing IOS Fundamental Exercises 2 1 Lab Exercise 1 Banner MOTD Setting Message of the Day 2 2 Lab Exercise 2 Setting Host Name 2 3 Lab

Related Books