ABS Module Removal amp Installation Instructions Chevy Express

Abs Module Removal Amp Installation Instructions Chevy Express-PDF Download

  • Date:28 Jul 2020
  • Views:3
  • Downloads:0
  • Pages:5
  • Size:255.47 KB

Share Pdf : Abs Module Removal Amp Installation Instructions Chevy Express

Download and Preview : Abs Module Removal Amp Installation Instructions Chevy Express


Report CopyRight/DMCA Form For : Abs Module Removal Amp Installation Instructions Chevy Express


Transcription:

ABS Module Removal Installation Instructions ModuleMaster. Support 208 892 0764,Chevy Express www modulemaster com. Disconnecting the Module,1 To disconnect the rectangular. plug insert a screwdriver under the,red plastic locking clip The EBCM. will of course be under your vehicle,when doing this. Removal Procedure,1 Find a level place to raise the vehicle.
2 Set the parking brake firmly,3 Put an automatic transmission shift lever in. PARK or shift a manual transmission to FIRST or,REVERSE gear 2 Pry the red locking clip into the. down position as shown,4 For 4 wheel drive vehicles be sure the transfer. case is in a drive gear not neutral,5 Turn off the engine. 6 Place wheel blocks behind the rear wheels, 7 Use jack stands to support the vehicle Never get.
under a vehicle when it is supported only by a, 8 Make sure the ignition is off when you disconnect. the module or it could be permanently damaged, 9 Remove the connector s from the module Continued on next page. Follow the steps on the right to avoid breaking,the plastic retaining clips. 10 Remove the screws that hold the module to the,hydraulic control unit If you cannot reach the. screws easily or if the heads have rusted tight,jump to the section Removing Difficult Modules.
11 Cover the exposed surface of the hydraulic unit. with aluminum foil Avoid driving your vehicle on,dusty or wet roads if possible Protect the plug. ABS Module Removal Installation Instructions ModuleMaster. Support 208 892 0764,Chevy Express www modulemaster com. ends of the cables from moisture with electrical, tape as well For those who have electronic four 3 Firmly squeeze the side of the. wheel drives 4WD may not function properly connector with your thumb as. until the ABS controller is reinstalled indicated while pulling at the same. 12 You can still drive your vehicle since the brakes time. will not be impaired by removal of the ABS,module On certain vehicles the speedometer. receives an input signal from the ABS module,and may not function until the module is back in.
Removing Difficult Modules, Most people have reported successful removal of the. ABS controller without disconnection of the brake lines. However you may have to disconnect all five 5 4 The connector will release as. hydraulic lines for successful removal if the roads you shown Some resistance is normal. drive on are salted and the Torx T20 bolts are rusted in due to friction from the rubber o ring. place In such circumstance it is best to remove the seal. entire ABS assembly from the truck for easier removal. of the ABS controller by drilling out the bolt heads. There is very little room to access these four bolts. under the truck in such stubborn cases It is suggested. that you disconnect the lines and remove the entire. assembly Take the assembly to a workbench or drill. press to drill grind the heads off of the bolts If this. sounds too ugly and disconnecting the five brake lines. will ruin your day you can instead remove the three hex. head bolts attaching the ABS pump manifold to the,vehicle frame and CAREFULLY lower it You must. ABS Module Removal Installation Instructions ModuleMaster. Support 208 892 0764,Chevy Express www modulemaster com. support the heavy pump assembly so you don t kink the. brake lines Then you will have room to get a small. grinder or Dremel Tool to grind the heads off of the evil. rusted bolts, Be sure to order a bolt replacement Kit to replace. rusted or stripped out Torx ABS module bolts,After removing the rusted bolts separate the EBCM.
from the hydraulic unit You do not need to worry about. any parts falling out and no fluid will leak out The six. protruding valve bodies are permanently pressed into. the aluminum housing and will not move or fall apart. while the EBCM is removed for the repair,Installation Procedure. 1 Installation is the reverse of the above steps,2 Removal of any of the brake lines will require. bleeding of the brakes upon re installation Your, vehicle is probably overdue for a brake fluid flush. anyways Brake fluid is hygroscopic absorbs,water and the water molecules will congregate. in the lowest parts of the brake system,eventually corroding critical brake components.
Modern vehicles should have their brake fluid,flushed on a regular basis so you are providing. your vehicle a much needed service in the,process of this repair. 3 Start the engine and make sure the brake, ABS Module Removal Installation Instructions ModuleMaster. Support 208 892 0764,Chevy Express www modulemaster com. warning lights go out,2009 and later vehicles, Please call to find out if we can repair your module.
ABS Module Removal amp Installation Instructions ModuleMaster Support 208 892 0764 www modulemaster com Chevy Express 1999 2008 Note We can only rebuild the Kelsey Hayes 325 module on right The Series 30 is similar but has a third connector as shown Both the Series 30 and 310 are unrepairable and must be replaced On most Chevy trucks the ABS module is mounted to the left frame rail

Related Books